[metallika]

Heips!

Nimelt sai soetatud töötav ketas(nägin ise, kui ostsin) - kasutatuna

kuid koju jõudes ei saa ma seda tööle

Olen proovinud teha nii lihtsalt mitmete arvutite LAN pesadesse paigutamist kui ka vastavalt kasutusjuhendile teinud ühendusi!

4-ja erineva arvuti vahel ei ole saanud tööle

olen proovinud mitmeid kaableid(LAN kaableid) kuid mitte midagi

olen proovinud eri OS-side peal - Windows XP 32-bit, Windows VISTA 32-bit, Windows 7 32-bit ja ka 64-bit - tulemus sama - ümmargune 0!

led valgustusega (on/off) lüliti põleb ja natuke suriseb ja ka ragiseb ketas - kuid ikka mitte mõhkugi!

olen proovinud ka vastavalt juhnditele ka eri programme (WD kodukalt ja ka WD kaasa tulnud plaadilt) kuid " NO NETWORK DEVICE FOUND" vms ja kogu kompott!

Kas keegi oskab öelda, milles viga?

Tänud ette ära juba

[Spezz]

Esimene mõte on, et kettale oli käsitsi ip määratud. Otsi, kuidas DHCP peale seada teda.

[metallika]

pole nii pädev network huinamuina alal aga eks ma uurin ja puurin

[Amperloom]

seadme täpsem nimi ja mudel ka, siis vähe lihtsam otsida ja aidata.

[metallika]

tegu siis sellise mudeliga: WD10000GO32-001

Western Digital My Book World Edition (storage system for remote access & sharing)

World Edition Network Interface

loodan, et on abi sellest

EDIT: 1TB RJ-45 aka LAN/Ethernet versioon

[Amperloom]

Spoiler

Follow the steps below to easily find your
My Book World Edition on the local area network
(LAN) in Windows XP/Vista using WD Discovery.
Skip to page 5 for Mac Leopard instructions or
page 6 for Mac Tiger instructions.
Note: The WD Discovery application on the
included CD should be installed on every PC
connected to the LAN from which you intend to
access your My Book World Edition.
Windows XP/Vista
1. Turn on your computer and wait for the
operating system to load.
2. Insert the software CD into the CD-ROM
drive.
Note: If AutoPlay is disabled on your
computer, you must install the utilities
manually. Click Start and point to Computer
(Windows Vista) or My Computer, then
double-click Setup.exe in the root directory of
the CD.
3. Windows Vista: Click Run setup.exe, then
click Allow.
4. Click Accept in the Terms of Agreement
screen.
5. If you have connected the My Book device
properly as shown in the Connect screen,
click Next.
6. The Application Installer screen opens,
displaying a list of options. Click WD
Discovery Tool.
7. Click Map Network Drive in the Things To
Do list.
8. Click Yes.
9. All share folders available on the device will
be mapped as network drives automatically.
Available drive letters are assigned
backwards from Z. When mapping
completes, the share folders appear as
network drives in the WD Discovery screen.
10. Click Start>Computer (Windows Vista) or
My Computer (Windows XP). The network
drives appear. You can now drag and drop
files into the network drive folders using My
Computer or Windows Explorer. See the
complete user manual on the CD for all other
basic and advanced device management
functions.

Oled teinud täpselt juhendi järgi?
Võimalus on veel see, et ruuter ei lase ühendust läbi....seadistuse viga

Väike soovitus veel:
Important: Wait for the My Book World Edition to finish powering up
(approximately three minutes) before configuring the device. During this
time, do not press the power button. The bottom LED on the front of the My
Book device fully illuminates.

[metallika]

olen proovinud jah

kuid egas mitu korda seda proovida pole paha asi!

proovin uuesti

[Amperloom]

Nu näed, oligi seadistuse kala....
Aga kui miskit on siis võta aga julgelt ühendust, äkki oskan aidata.

[metallika]

tavaiks!

aga üks jama on

peaks laskma mingi 30 vai rohkem mega sekis kuid laseb alla 10mb sekis - see on hetkel ainuke jama