[szultz]

Et sai teine just ostetud, aga ei taha teine DMA (direct memory access) sisse lülitada, panen küll linnukese ja teen restardi aga peale restarti on ikka maas, kas ei toeta teine DMA-d või tuleb tagasi viia. Sest praega kirjutab ta mul 8X kiirusega plaatinumi toorikule 4 giga umbes pool tundi, see ei ole ju normaalne, kui käima panin näitas reemaining time 6.20 ja see tiksus ilusti selle ajaga ka nulli, kuid kirjutamine ise oli vast 15 % juures.

Edit: Uuendasin emme( VIA kiibistikul) driverieid VIA kodulehelt, panin nero 6 e Nero expressi asemele mis oli softi plaadil kirjutajaga kaasas. Seal oli sihuke option nagu speed measurment, panin sellegi prooviks peale, tulemus oli 24,7x aga kui plaati kirjutama hakkan siis kirjutab ikka sama aeglaselt
Njah homme üritan tagasi viia, täna kartulisalong kinni.

[Juhuslik]

See ei ole kirjutaja ega kartulisalongi viga.
Äkki annad tiba rohkem infi oma raua kohta...
Ja võid ju ka vaadata kas BIOS'is on DMA lubatud. Juhul, kui selline asi seal on.
Kindlasti pane kirjutaja jumper MASTER'iks ja kasuta kõvakettast eraldi asetsevat IDE kanalit.
CABLE SELECT ei meeldi eriti ühelegi kirjutajale.

[szultz]

Ketas on primari master
Kirjutaja secondary master
Vana Samsungi CD-RW on secondary slave(varasem Sec master) ja sellel on DMA enabletud, seega arvuti võimaldab DMA-d, ei võimalda aga seda mikskipärast DVD kirjutajale.
Arvuti ise on P4 HT prescott 3.0GHz, VIA PT 880 või PT 800 kiibistikul emmega, Primary IDE controller ja Secondary IDE controller, samuti VIA Bus master IDE controller on kõik microsofti driveritel, mälu tootjat ei oska praega lambist öelda PC3200 400 MHz DDRAM on teine muidu(1x 256 MB pulk), muu ei oma nagu tähtsust vast, OS Win XP PRO SP2, automatic uptates on enabletud ja tehtud kõik, probleeme on tekkinud vaid VIA integreeritud võrgukaardi mingi update installiga mille sain ka lõpuks tehtud siiski.

Kas ei või see kirjutaja riistvaraline viga siiski olla et DMA ei funka?
Ei paku nagu erilist pinget nii aeglane kirjutamine, kui ei ole riistvaraline viga siis on igasugune abi selle tarkvaraliseks lahendamiseks enam kui teretulnud.

[XYZ]

Hea test oleks eraldi pardile teha veel üks uus puhas win install ja vaadata kuidas seal DMA-ga lood on.

[Juhuslik]

[szultz]

[TXX]

Endal nec 3500 ag (2.19)kirjutab via kt400A peal 8x kiirusega ka kuskil pool tundi 4giga aga sama kirjutaja kirjutab nforce2 kiibistikuga plaadil 8-9 minutit tervet plaati ehk 4,3giga.

[szultz]

[Juhuslik]

[SCREAMER]

firmware uuedndus? (1.02)
http://au.lgservice.com/jsp/common/download.jsp?DOC_ID=KRSWL000012941&FILE_NAME=KRSWL000012941-b1-a1.zip&ORIGINAL_NAME_b1_a1=GSA-4163A102(EW).zip&FILE_GUBUN=B

[JanQ]

Mäletan, et kunagi mingites foorumites jahuti kõvasti VIA (ka nForce) kiibistikest ja nende draiverite kokkusobimatusest
kirjutajatega. Soovitati isegi Inteli default draivereid. Otsi inffi writerite foorumitest.

[TXX]

[szultz]

Nii sain kirjutaja UDMA mode 2, selleks oli vaja device managerist secondary IDE cabel'i driverile uninstall teha ja peale rebooti oli DMA mode peal, nüüd aga kimbutab mind järgmine kala, kui panen kirjutama siis kohe peale lead in'i tekib Communication failure error

LOG:
Daemien Lucifer
Hell Inc.

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 26.10.04 18:35:34
Nero Version: 6.6.0.14
Internal Version: 6, 6, 0, 14d
(Nero Express)
Recorder: <HL-DT-ST DVDRAM GSA-4163B>Version: A103 - HA 1 TA 0 - 6.6.0.14
Adapter driver: <atapi> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM: <Generic DVD-ROM >Version: 1.0 - HA 2 TA 0 - 6.6.0.14
Adapter driver: <d344prt> HA 2

=== Scsi-Device-Map ===
DiskPeripheral : ExcelStor Technology J880 atapi Port 0 ID 0 DMA: On
CdRomPeripheral : HL-DT-ST DVDRAM GSA-4163B atapi Port 1 ID 0 DMA: On
CdRomPeripheral : Generic DVD-ROM 1.0 d344prt Port 2 ID 0 DMA: Off

=== CDRom-Device-Map ===
HL-DT-ST DVDRAM GSA-4163B E: CDRom4
Generic DVD-ROM G: CDRom1
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 40894464 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 254MB (260588kB)
Free physical memory: 61MB (62616kB)
Memory in use : 75 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

28.6.2005
UDF compilation
17:48:18 #1 Text 0 File Isodoc.cpp, Line 6314
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE

17:48:18 #2 Text 0 File Reader.cpp, Line 127
Reader running

17:48:18 #3 Text 0 File Writer.cpp, Line 122
Writer HL-DT-ST DVDRAM GSA-4163B running

17:48:18 #4 Text 0 File Burncd.cpp, Line 3230
Turn on Disc-At-Once, using DVD media

17:48:18 #5 Text 0 File DlgWaitCD.cpp, Line 267
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2153231 (478:29.56, 4205MB)

17:48:18 #6 Text 0 File DlgWaitCD.cpp, Line 279
Write in overburning mode: NO (enabled: CD)

17:48:18 #7 Text 0 File DlgWaitCD.cpp, Line 2433
Recorder: HL-DT-ST DVDRAM GSA-4163B, Media type: DVD-R
Disc Manufacturer: CMC MA - G. AE1
Disc Application Code: 64, Disc Physical Code: 193

17:48:18 #8 Text 0 File DlgWaitCD.cpp, Line 445
>>> Protocol of DlgWaitCD activities: <<<
=========================================

17:48:18 #9 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2153232 (2153232) = #2153232/478:29.57
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2153232 blocks [HL-DT-ST DVDRAM GSA-4163B]
--------------------------------------------------------------

17:48:18 #10 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [HL-DT-ST DVDRAM GSA-4163B] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4409819136, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2153232 | lead-out | 1 | 0x41 | 0x00

17:48:18 #11 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started

17:48:18 #12 Text 0 File Burncd.cpp, Line 4114
Cache writing successful.

17:48:18 #13 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed

17:48:18 #14 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 8x (11 080 KB/s)

17:48:18 #15 Text 0 File ThreadedTransferInterface.cpp, Line 2643
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

17:48:19 #16 Text 0 File DVDR.cpp, Line 2316
Recording mode: Sequential Recording Mode

17:48:19 #17 Text 0 File Mmc.cpp, Line 21592
Set BUFE: Buffer underrun protection -> ON

17:48:19 #18 Text 0 File DVDR.cpp, Line 2470
Start write address at LBA 0
DVD high compatibility mode: Yes

17:48:19 #19 Text 0 File Cdrdrv.cpp, Line 8821
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 30 00 10 20 00 00 00 - 00 00 00 21 00 00 00 00 .0.........!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

17:48:40 #20 Text 0 File Cdrdrv.cpp, Line 1288
17:48:40.421 - HL-DT-ST DVDRAM GSA-4163B\H1 T0 : Queue again later

17:48:54 #21 SCSI -1024 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x09090000
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x04 (KEY_HARDWARE_ERROR)
Sense Code: 0x08
Sense Qual: 0x03
CDB Data: 0x2A 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x10
0x00 0x00 0x00 0x0C 0x08 0x03

17:48:54 #22 CDR -1024 File Writer.cpp, Line 311
Communication failure

17:48:54 #23 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

17:48:54 #24 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader

17:48:54 #25 Text 0 File DVDR.cpp, Line 2708
EndDAO: Last written address was 255

17:49:22 #26 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 8x (11 080 KB/s)


Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.28a, size=20640 bytes, created 12.03.05 01:28:14 (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 03.08.04 22:59:44 (Adapter driver for rec)
File 'Drivers\d344prt.sys': Ver=3.44.0.0 built by: WinDDK, size=5248 bytes, created 27.12.03 02:38:10 (Adapter driver for src)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

[XeStAiSy]

ennemgi sellist kala n6htud, proovi IDE kaabli pistik t6sta teisse pistikusse. See kaabel v6ib olla vigane ja ei anna korralikult kontakti.

[szultz]